JIS A0009-1970 建筑物活动隔墙构件的公称尺寸

上一篇: JIS A1451-1970 建筑材料及建筑构件的磨耗试验方法(采用回转圆盘磨擦与冲击地板材料的磨耗试验方法)
下一篇: JIS M8512-1970 耐火原材料耐火性试验方法

【英文标准名称】:Roadvehicles-Cleanlinessofcomponentsoffluidcircuits-Part7:Particlesizingandcountingbymicroscopicanalysis
【原文标准名称】:道路车辆.液压管路部件清洁度.第7部分:显微分析测量粒径和计数
【标准号】:ISO16232-7-2007
【标准状态】:现行
【国别】:国际
【发布日期】:2007-06-01
【实施或试行日期】:2007-06-01
【发布单位】:国际标准化组织(IX-ISO)
【起草单位】:ISO/TC22
【标准类型】:()
【标准水平】:()
【中文主题词】:空调器;清洁(度);清洁度值;污染物;污染;冷却剂;萃取;萃取分析法;过滤;液压管路;液压传动;内燃机;实验室试验;液体;测量;膜过滤器;方法;显微分析;摩托车;粒径分析;粒度分布;粒度;颗粒;制冷剂;道路车辆零部件;道路车辆;抽样方法;抽样表;扫描电子显微镜;固态润滑剂;试验报告;测试;运载工具部件
【英文主题词】:Airconditioners;Cleanliness;Cleanlinessvalue;Contaminants;Contamination;Coolants;Extraction;Extractionmethodsofanalysis;Filtering;Fluidcircuits;Hydraulicfluidpower;Internalcombustionengines;Laboratorytests;Liquids;Measurement;Membranefilters;Methods;Microscopicanalysis;Motorvehicles;Particlesizeanalysis;Particlesizedistribution;Particlesizes;Particles;Refrigerants;Roadvehiclecomponents;Roadvehicles;Samplingmethods;Samplingtables;Scanningelectronmicroscopes;Solidlubricants;Testreports;Testing;Vehiclecomponents
【摘要】:ThispartofISO16232definesmethodsfordeterminingthesizeandnumberofcontaminantparticles,whichhavebeenextractedfromcomponentsanddepositedonthesurfaceofamembranefilter,asdeterminedbyusingeitheralightopticalmicroscope(LM)orascanningelectronmicroscope(SEM).Theresultofthismeasurementistheparticlesizedistributiononthemembranefilter.Asthefunctionofpartsandcomponentscanbeimpairedbythepresenceofasingleorafewcriticalparticles,acompleteanalysisofthetotalmembranefiltersurfaceisessential.TheseanalysescanbeperformedeithermanuallyorautomaticallyusingImageAnalysis(IA)techniquesiftheappropriateequipmentisavailable.
【中国标准分类号】:T32
【国际标准分类号】:13_040_50;43_180
【页数】:30P.;A4
【正文语种】:英语


Product Code:SAE J1773
Title:SAE Electric Vehicle Inductively Coupled Charging
Issuing Committee:Hybrid - Ev Committee
Scope:This SAE Recommended Practice establishes the minimum interface compatibility requirements for electric vehicle (EV) inductively coupled charging for North America.This part of the specification is applicable to manually connected inductive charging for Levels 1 and 2 power transfer. Requirements for Level 3 compatibility are contained in Appendix B. Recommended software interface messaging requirements are contained in Appendix A.This type of inductively coupled charging is generally intended for transferring power at frequencies significantly higher than power line frequencies. This part of the specification is not applicable to inductive coupling schemes that employ automatic connection methods or that are intended for transferring power at power line frequencies. in the charge coupler). The charge controller signals the charger to stop charging when it determines that the batteries are completely charged or a fault is detected during the charging process.The following steps correspond with the diagram in Figure 1, and describe the closed-loop charging system.Vehicle charge controller determines desired current into batteries. **Vehicle charge controller transmits charger output power request to charger via an IR communications interface. **Charger controls input current from utility based on charger output power request from vehicle charge controller. **Charger converts 60 Hz utility power to HFAC power.HFAC power is magnetically coupled from the coupler (primary) to the vehicle inlet (secondary).HFAC power is rectified/filtered to DC to charge the vehicle batteries.Process repeats until the vehicle charge controller determines the batteries are fully charged. **Items with ** indicate control loop.?Typical closed-loop charging system.